Enter Your Email Address For

An Instant $5.00 OFF Coupon!


Find My Remote or Key Now !

Keyless Entry Remote Programming

  • 2007-2009 Acura MDX Remote Key Programming Information

    Acura MDX Programming Instructions

    2007-2009 Acura MDX Remote Key Programming Information

     

    1. Have your remote/key ready.

    2. Sit in the vehicle with all the doors and the trunk closed.

    3. Turn the ignition to the "ON" position, the dashboard lights will turn on.

    4. You will hear a soft clicking sound. Within 5 seconds hold the “Lock” button on the remote for about 1 second.

    5. Turn the ignition to the "OFF" position. The dashboard lights will turn off. If you hear a soft clicking sound, you must start everything over.

    6. Repeat these steps three more times.

    7. When you turn the ignition to the "ON" position for the 4th time, press the lock button on one of the remotes. The car door locks will make a sound. The door locks will not lock or unlock now. They would just make a noise. The vehicle's system is now in programming mode. Do not turn key off. Press the lock button 2 more times then press unlock.

    8. Turn ignition completely off and remove the key.

    9. Remove yourself from the vehicle. The remotes should now function. If you have a trunk release, you will need to press the button for a couple seconds for it to open.

     

    Special Notes:

    Each step in the instructions must be executed in 5 seconds or less for the programming to be successful.

    Please click here to locate a professional automotive locksmith in your area if you are unable to successfully program this remote.

  • 2002 Nissan Altima Keyless Remote Programming Instructions

    2002 Nissan Altima Remote Programming

    1. Close and lock all the vehicle doors with the driver's side power lock / unlock switch located on driver’s door panel.

    2. Insert the key into ignition and remove it from the ignition key cylinder at least 6 times within 10 seconds. Your hazard lamps will flash if you have performed this step successfully.

    3. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed to fast, system will not enter programming mode.

    4. Insert the key into ignition and turn to the ACC position.

    5. Within 5 seconds, push any button on the keyless remote. Your hazard lamps should flash.

    6. NOTE: Do not press the button on the remote more than one time or the programming will not be successful.

    7. If there are any remaining remotes, including the old ones, unlock then lock all doors using the switch on driver’s door panel and within 5 seconds press any button on the next remote. Your hazard lamps should flash. You should repeat this step for each additional remote including any current existing remotes.

    8. Turn the key to the off position then remove the key from the ignition. Unlock the door using the switch on door panel then open driver’s door.

    9. Test remote all remotes.

    Please click here to locate a professional automotive locksmith in your area if you are unable to successfully program this remote.

  • 2000 - 2011 Ford Focus Keyless Remote Programming Instructions

    Ford-Focus

    1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode.

    2. Within 20 seconds press any button on first keyless remote. Door locks will cycle to confirm programming.

    3. Within 20 seconds, press any button on second keyless remote. Door locks will cycle again to confirm programming.

    4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

    Please click here to locate a professional automotive locksmith in your area if you are unable to successfully program this remote.

  • 2004 - 2006 Buick Rainier Keyless Entry Remote Programming Instructions

    2005-buick-rainier-cxl_100030639_m

    1. Close all the vehicle doors.
    2. Insert the key into the ignition.
    3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.
    4. Perform steps 5 through 8 in fairly rapid succession.
    5. Turn the ignition switch to the ON position without starting the engine
    6. Turn the ignition switch to the OFF position.
    7. Turn the ignition switch to the ON position.
    8. Turn the ignition switch to the OFF position.
    9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
    10. Hold down the LOCK and UNLOCK buttons on the keyless remote simultaneously until the door locks and unlocks. This may take 30 - 45 seconds.
    11. Repeat step 10 for ALL additional keyless remotes.
    12. Turn the ignition switch to the ON position in order to exit the keyless remote programming mode.

    Please click here to locate a professional automotive locksmith in your area if you are unable to successfully program this remote.

  • 2013 Acura TL Keyless Remote Programming Instructions

    fa7420660a0d028a00ef9525ace1f7a4

    There are no self-programming instructions or methods for this vehicle. You will need to contact a local automotive locksmith to program the keyless remote to this vehicle.

    Please click here to locate a professional automotive locksmith in your area.

  • 2012 Kia Rio Keyless Remote Programming Instructions

    Kia-Rio-2012-exterior

    There are no self-programming instructions or methods for this vehicle. You will need to contact a local automotive locksmith to program the keyless remote to this vehicle.

    Please click here to locate a professional automotive locksmith in your area.

  • Kia Soul 2010 Keyless Remote Programming Instructions

    2010_kia_soul_image

    There are no self-programming instructions or methods for this vehicle. You will need to contact a local automotive locksmith to program the keyless remote to this vehicle.

    Please click here to locate a professional automotive locksmith in your area.

7 Item(s)

1