2015 - 2020 Chevrolet 6 Button Smart Remote - Emergency key included - 315Mhz - HYQ1AA

Dealer Price $359.99 Your Price $153.00 You save $206.99 That's 57.5% OFF dealer price!
Availability: In stock
SKU
6102

IMPORTANT: Verify your remote is 315Mhz before purchasing as these vehicles could also take the 433Mhz remote. You can also verify by the FCC ID number. This item is for push-button-start vehicles. If you use an ignition key to start the vehicle, this item will not work for you. 


Ekey: 6101


Fits:

2015 - 2020 Chevrolet Suburban
2015 - 2020 Chevrolet Tahoe

180 Day Satisfaction Guarantee!

If you are not 100% satisfied with your product for any reason, you may return the product within 180 days of ordering for a replacement. Please see our return policy for further information.

 

More Information
SKU6102
FCC NumberHYQ1AA
OE Part #13529634, 13580802, 13508278
SupportYour purchase gives you 100% free e-mail and phone technical support from our expert staff.
Programming InformationThis remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab.
Product ConditionRefurbished
Programming Instructions

Programming WITH a Recognized Transmitter (Keyless Access Vehicles Only)

A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be off and all transmitters, both currently recognized and new, must be with you.

1. Remove the key from the recognized transmitter.

2. Place the recognized transmitter(s) in the cupholder or on the passenger seat.

3. Insert the vehicle key into the key lock cylinder on the driver door handle. Then turn the key counterclockwise, to the unlock position, five times within 10 seconds. The Driver Information Center (DIC) displays READY FOR REMOTE#2, 3, 4, ETC.

4. Place the new transmitter in the transmitter pocket/insert. Open the center console storage area and the storage tray. The transmitter pocket/ insert is in front of the storage area next to the center console storage area between the driver and front passenger seats.

5. Press the ENGINE START/ STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.

6. Remove the transmitter from the transmitter pocket and press unlock or lock on the transmitter.

To program additional transmitters, repeat Steps 4–6. When all additional transmitters are programmed, press and hold the ENGINE START/ STOP button for approximately 12 seconds to exit programming mode.

7. Return the key back into the transmitter.

 

Programming WITHOUT a Recognized Transmitter (Keyless Access Vehicles Only)

If there are no currently recognized transmitters available, follow this procedure to program up to eight transmitters. This feature is not available in Canada. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all transmitters to be programmed must be with you.

1. Remove the vehicle key from the transmitter.

2. Insert the vehicle key into the key lock cylinder on the driver door handle; then turn the key counterclockwise, to the unlock position, five times within 10 seconds. The Driver Information Center (DIC) displays REMOTE LEARN PENDING, PLEASE WAIT.

3. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/STOP button. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.

4. Repeat Step 3 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show READY FOR REMOTE # 1.

5. Place the new transmitter in the transmitter pocket/insert. Open the center console storage area and the storage tray. The transmitter pocket/ insert is in front of the storage area next to the center console storage area between the driver and front passenger seats.

6. Press the ENGINE START/ STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.

7. Remove the transmitter from the transmitter pocket/insert and press unlock or lock on the transmitter.

To program additional transmitters, repeat Steps 5–7. When all additional transmitters are programmed, press and hold the ENGINE START/ STOP button for approximately 12 seconds to exit programming mode.

8. Return the key back into the transmitter.

msrp359.99