Enter Your Email Address For

An Instant $5.00 OFF Coupon!

Find My Remote or Key Now!

1993 - 1996 GM 3 Button Keyless Entry Remote - ABO0103T (Buick logo)

Availability: In stock

Dealer Price: $94.15

$34.99

You Save: $59.16

That's 62.84% OFF Dealer price!

This is an authentic factory/OEM device meant to operate your specific vehicle.

62.84%
off

1993 - 1996 GM 3 Button Keyless Entry Remote - ABO0103T (Buick logo)

More Views

1993 - 1996 GM 3 Button Keyless Entry Remote - ABO0103T (Buick logo)



Fits:

1994 - 1996 Oldsmobile Achieva
1993 - 1996 Buick Century
1993 - 1996 Buick Regal
1993 - 1995 Buick Roadmaster
1993 - 1995 Buick Skylark
1993 - 1995 Chevrolet Caprice

Additional Information

SKU 355
FCC Number ABO0103T
OE Part # 10205239
Support Your purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee! If you are not 100% satisfied with your product for any reason, you may return the product within 180 days of ordering for a replacement. Please see our return policy for further info
Programming Information Please Check if your vehicle has Self-Programming instructions by Clicking the Tab Above. "Programming Instructions"
Product Condition Refurbished
Manufacturer's Suggested Retail Price $94.15

1994 - 1996 Oldsmobile Achieva Programming Instructions:

1.  Locate the programming connector located in the LH trunk. Trim may
     have to be pulled back to access programming connector. ( Connector
     has wires leading up to it and it is not connected to anything.)

2.  Jump programming connector terminals. Leave terminals jumped
     unitl step 6.

3.  System should now lock and unlock doors to indicate 
      programming mode has been entered. 

4.  Press any button on keyless remote once.
     System should now lock and unlock doors, indicating successful 
     programming of keyless remote.  

5.  Repeat step 4 for additional remote or other existing keyless remote.
     
     NOTE: A maximum of only two Keyless Remotes can be programmed.

6.  Remove programming connector jumper wire to exit programming mode.

7.  Test remote(s).

 

1993 - 1996 Buick Century Programming Instructions:

1.  Locate the green programming connector located in the LH trunk. Trim may
     have to be pulled back to access programming connector. ( Connector
     has wires leading up to it and it is not connected to anything.)

2.  Jump programming connector terminals.

3.  System should now lock and unlock doors and trunk lid to indicate 
      programming mode has been entered. Trunk lid must have activated
      before proceeding.

4.  Press any button on keyless remote once.
     System should now lock and unlock doors and trunk lid, indicating 
     successful programming of keyless remote. Trunk lid must have
     activated before proceeding. 

5.  Repeat step 4 for additional remote or other existing keyless remote.
     
     NOTE: A maximum of only two Keyless Remotes can be programmed.

6.  Remove programming connector jumper wire to exit programming mode.

7.  Test remote(s).

1993 - 1996 Buick Regal Programming Instructions:

NoteExisting keyless remotes will be erased with this procedure.
          Existing working remotes will have to reprogrammed also.

1. Locate the programming connector wire located in the RH trunk area.
    You may have to pull back right side trunk trim on trunk wall to locate 
    the single black/white wire.

2. The programming connector wire should have one termial in the plastic
    connector on end of black/white wire. Ground the terminal in the connector
    to  a nearby bolt or trunk latch.
    Leave connector wire connected to ground through out procedure.

3. System will now lock and unlock doors automatically to indicate 
    programming mode has been activated.

4. Press any button on keyless remote. System will respond by locking 
    and unlocking doors one time to indicate successful programming.

5. Repeat step 4 for to program any additonal keyless remotes including
    and existing keyless remotes. Do not remove ground wire between
    programming of keyless remotes.

6. Disconnect programming connector wire from ground to exit programming
    mode.

7. Test keyless remote(s).

 

1993 - 1996 Buick Roadmaster Programming Instructions:

1.  Locate the programming connector located in the LH trunk. Trim may
     have to be pulled back to access programming connector. ( Connector
     has black/white wires leading up to it and it is not connected to anything.)

2.  Jump programming connector terminals. Leave terminals jumped
     unitl step 6.

3.  System should now lock and unlock doors to indicate 
      programming mode has been entered. 

4.  Press any button on keyless remote once.
     System should now lock and unlock doors, indicating successful 
     programming of keyless remote.  

5.  Repeat step 4 for additional remote or other existing keyless remote.
     
     NOTE: A maximum of only two Keyless Remotes can be programmed.

6.  Remove programming connector jumper wire to exit programming mode.

7.  Test remote(s).

 

1993 - 1996 Buick Skylark Programming Instructions:

 

1.  Locate the green programming connector located in the LH trunk. Trim may
     have to be pulled back to access programming connector. ( Connector
     has wires leading up to it and it is not connected to anything.)

 

2.  Jump programming connector terminals.

 

3.  System should now lock and unlock doors and trunk lid to indicate 
      programming mode has been entered. Trunk lid must have activated
      before proceeding.

 

4.  Press any button on keyless remote once.
     System should now lock and unlock doors, indicating successful 
     programming of keyless remote.  

 

5.  Repeat step 4 for additional remote or other existing keyless remote.
     
     NOTE: A maximum of only two Keyless Remotes can be programmed.

 

6.  Remove programming connector jumper wire to exit programming mode.

 

7.  Test remote(s).

 

1993 - 1996 Chevrolet Caprice Programming Instructions:

 

1. Access programming connector in LH side of trunk (drivers side). Programming connector will be close to the tail light, it will not be connected to anything and should be one black and one white wire. It will have a plastic connector on the end of it with two holes in it or ports.

 


2. Jump programming connector using a suitable jumper wire. Jumping the connector means to use a wire or paperclip bent in the shape of a U to make a connection between the two ports. Be sure you are making contact with the metal inside both ports.

 


3. System should now lock and unlock doors and activate trunk release to indicate successful entry into programming mode.

 


4. Press any button on remote one time. System should now lock and unlock doors and activate trunk release to indicate successful programming of remote.

 


5. Repeat step 4. for each additional remote including working ones.

 


6. To exit programming mode remove jumper wire and test all remotes.


Customer Reviews of Our Service
Please Note: Reviews about self-programming do not indicate the product above is self-programmable. Please inquire about each product.
Back up
1
Get Your Coupon Now for
3% Off Your Purchase!
Receive a 3% Off Coupon Code in Your email within just minutes by simply signing up for our Newsletter. Then, just apply the coupon code at checkout for Your Savings.