Enter Your Email Address For

An Instant $5.00 OFF Coupon!

Find My Remote or Key Now!

2010 - 2017 Buick 5 Button Remote Flip Key w/ Remote Start - PEPS - OHT05918179

Availability: In stock

Dealer Price: $114.98

$45.99

You Save: $68.99

That's 60% OFF Dealer price!

this link

2-Years Extended Warranty Plan

Replace My Remote offers an optional Extended 2-Year warranty on all remote and remote key products for Only $7.99. You can view the full terms and coverage of the warranty by clicking the  blue "View All Terms" link. Simply check the "Warranty" check box to add the 2 year extended warranty to your product.

This is an authentic factory/OEM device meant to operate your specific vehicle.

60%
off

2010 - 2017 Buick 5 Button Remote Flip Key w/ Remote Start - PEPS - OHT05918179

More Views

2010 - 2017 Buick 5 Button Remote Flip Key w/ Remote Start - PEPS - OHT05918179

This is for vehicles with a PEPS (Passive Entry Passive Start) System.

Fits:

2010 - 2012 Buick Allure
2010 - 2016 Buick Lacrosse
2011 - 2017 Buick Regal
2012 - 2016 Buick Verano

Additional Information

SKU 352
FCC Number OHT05918179
OE Part # 13500224, 5912559, 13504202, 13585206
Support Your purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee! If you are not 100% satisfied with your product for any reason, you may return the product within 180 days of ordering for a replacement. Please see our return policy for further info
Programming Information This remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab.
Product Condition Refurbished
Manufacturer's Suggested Retail Price $114.98

Programming with a Recognized Transmitter (Keyless Access Vehicles Only)


A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be off and all of the transmitters, both currently recognized and new, must be with you.

1. Place the recognized transmitter(s) in the cupholder.

2. Insert the vehicle key of the new transmitter into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays READY FOR REMOTE #2, 3, 4 or 5.

3. Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console cupholder. The cupholder liner will need to be pulled out to access the transmitter pocket.

4. Press the ignition. When the transmitter is learned, the DIC will show that it is ready to program the next transmitter.

5. Remove the transmitter from the transmitter pocket and press K. To program additional transmitters, repeat Steps 3 through 5.

When all additional transmitters are programmed, press and hold the ignition for 10 seconds to exit programming mode.


Programming without a Recognized Transmitter (Keyless Access Vehicles Only)


If there are no currently recognized transmitters available, follow this procedure to program up to five transmitters. This feature is not available in Canada. This procedure
will take approximately 30 minutes to complete. The vehicle must be off and all of the transmitters you wish to program must be with you.

1. Insert the vehicle key of the transmitter into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays REMOTE LEARN PENDING, PLEASE WAIT.

2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press the ignition. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.

3. Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show READY FOR REMOTE # 1.

4. Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console cupholder. The cupholder liner will need to be pulled out to access the transmitter pocket.

5. Press the ignition. When the transmitter is learned, the DIC will show that it is ready to program the next transmitter.

6. Remove the transmitter from the transmitter pocket and press K. To program additional transmitters, repeat Steps 4 through 6.

When all additional transmitters are programmed, press and hold the ignition for 10 seconds to exit programming mode.

Customer Reviews of Our Service
Please Note: Reviews about self-programming do not indicate the product above is self-programmable. Please inquire about each product.
Back up
1