Enter Your Email Address For

An Instant $5.00 OFF Coupon!

Find My Remote or Key Now!

1996 - 2002 GM 4 Button Keyless Entry Remote Fob - AB01502T/ABO1502T

Availability: In stock

Dealer Price: $109.30

$44.99

You Save: $64.31

That's 58.84% OFF Dealer price!

this link

2-Years Extended Warranty Plan

Replace My Remote offers an optional Extended 2-Year warranty on all remote and remote key products for Only $7.99. You can view the full terms and coverage of the warranty by clicking the  blue "View All Terms" link. Simply check the "Warranty" check box to add the 2 year extended warranty to your product.

This is an authentic factory/OEM device meant to operate your specific vehicle.

58.84%
off

1996 - 2002 GM 4 Button Keyless Entry Remote Fob - AB01502T/ABO1502T

More Views

1996 - 2002 GM 4 Button Keyless Entry Remote Fob - AB01502T/ABO1502T

Fits:

1999 - 2000 Cadillac Escalade
1996 - 2002 Chevrolet Camaro
1996 - 1999 Chevrolet Cavalier
1996 - 1999 Chevrolet Lumina
1996 - 1999 Chevrolet Malibu
1996 - 1999 Chevrolet Monte Carlo
1997 - 1998 Oldsmobile Achieva
1997 - 1999 Oldsmobile Cutlass
1996 - 2002 Pontiac Firebird
1997 - 1998 Grand AM
1997 - 1998 Pontiac Grand Prix
1997 - 1999 Pontiac Sunfire
1997 - 1999 Saturn SC
1996 - 1999 Saturn SL
1997 - 1999 Saturn SW

Additional Information

SKU 916
FCC Number AB01502T/ABO1502T
OE Part # 16245100-29
Support Your purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee! If you are not 100% satisfied with your product for any reason, you may return the product within 180 days of ordering for a replacement. Please see our return policy for further info
Programming Information This remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab. NOTE: When looking under the 'Programming Instructions' tab please look for your specific model as the programming instructions vary.
Product Condition Refurbished
Manufacturer's Suggested Retail Price $109.30

1996 - 2002 Chevrolet Camaro

1997 - 1999 Pontiac Firebird

1.      Turn the ignition switch to the OFF position.    

2.      Remove the RADIO fuse.    

3.      Cycle the ignition switch from the OFF position to the RUN position (as far as you can go without
      cranking the engine) 3 times within 5 second ending in the RUN position. The vehicle will verify
      entry into the programming mode by locking then unlocking the door locks.    

4.      Press and hold both the LOCK and UNLOCK buttons on the first transmitter for approximately
      15 seconds. The vehicle will verify programming by locking then unlocking the door locks. Your
      new remote has been accepted and all existing remote codes have been erased.    

5.      Repeat the previous step for each additional transmitter (including any existing transmitters). You
      may program up to 4 transmitters. This must be done before the RADIO fuse is reinstalled.    

6.      Place the ignition switch in the OFF position. IMPORTANT: The remote keyless entry system
      will not be operational if the radio fuse is open.    

7.      Replace the RADIO fuse. If at any time it is necessary to restart the procedure, turn the ignition
      OFF and proceed again with step number 1.


1996 - 1999 Chevrolet Cavalier

1997 - 1998 Oldsmobile Achieva

1997 - 1998 Grand AM

1997 - 1999 Pontiac Sunfire

 

1.      Make sure ignition is in the OFF position.    

 

2.      Locate the Programming Connector in the trunk (driver’s side). It is a
      plastic connector with two wires leading up to it. The connector is not
      plugged into anything. You may have to pull back trim to access the
      connector.    

 

3.      The programming connector should have two terminals. Connect both
      terminals with a suitable jumper wire. Make sure the terminals remain
      connected throughout the programming procedure.    

 

4.      Press the LOCK and UNLOCK buttons on the transmitter simultaneously.
      In response, the Keyless Entry Module will cycle all the Door Lock Motors
      at once. Your new remote has been accepted and all existing remote codes
      have been erased.    

 

5.      Repeat the previous step for each additional transmitter (including any
      existing transmitters). Do not remove jumper wire in between programming
      of transmitters.    

 

6.   Remove the jumper wire from the Keyless Programming Connector.


1996 - 1999 Chevrolet Lumina

1996 - 1999 Chevrolet Monte Carlo

Note: Existing keyless remotes will be erased with this procedure.
         Existing working remotes will have to reprogrammed also.

1. Locate the programming connector wire located in the RH trunk area.
    You may have to pull back right side trunk trim on trunk wall to locate
    the single black/white wire.

2. The programming connector wire should have one termial in the plastic
    connector on end of black/white wire. Ground the terminal in the connector
    to  a nearby bolt or trunk latch.
    Leave connector wire connected to ground through out procedure.

3. System will now lock and unlock doors automatically to indicate
    programming mode has been activated.

4. Press and hold the LOCK and UNLOCK buttons on keyless remote at the
    same time for 15 seconds or until the door locks lock and unlock once. 
    This indicates that your new keyless remote has been programmed and
    all other existing remotes have been erased.

5. Repeat step 4 for to program any additonal keyless remotes including
    and existing keyless remotes. Do not remove ground wire between
    programming of keyless remotes.

6. Disconnect programming connector wire from ground to exit programming
    mode.

7. Test keyless remote(s).


1997 - 1999 Chevrolet Malibu

1997 - 1999 Oldsmobile Cutlass

1.      Make sure ignition is in the OFF position.   

2.      Locate the Programming Connector in the trunk (center of rear shelf). It is a plastic connector with
      two wires leading up to it. The connector is not plugged into anything. You may have to pull back
      trim to access the connector.  

3.      The programming connector should have two terminals. Connect both terminals with a suitable
      jumper wire. The Keyless Entry Module will lock then unlock all the door lock motors once. Make
      sure the terminals remain connected throughout the programming procedure.  

4.      Press and hold the LOCK and UNLOCK buttons on the transmitter simultaneously for at least 15
      seconds or until the vehicle automatically locks and unlocks the door locks. Your new remote has
      been accepted and all existing remote codes have been erased.  

5.      Repeat the previous step for each transmitter to be programmed. Do not remove jumper wire in
      between programming of transmitters.  

6.      Remove the jumper wire from the Keyless Programming Connector.


1997 - 1998 Pontiac Grand Prix

 

IMPORTANT: Before entering programming mode, have in possession all of the remotes you
will be useing on the vehicle. Once you program the remote. all previous remotes that were
programmed will be erased from memory. The other remotes will not be functional until you
program the them again.

 

1. Remove the key from the ignition.

 

2. Close all doors.

 

3. Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or
    owner's manual to properly locate the "MALL PGM" fuse.

 

4. Insert the key into the ignition, and turn to the ACC position.

 

5. Turn the key to OFF and then back to ACC within 1 second.

 

6. Open and close any vehicle door. A chime will be heard when the system enters into
    programming mode.

 

7. Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds.
              IMPORTANT: After 7 seconds, a chime may be heard confirming successful
    synchronization. It is necessary to wait approximately 14 seconds for a second chime
    that will confirm successful programming.

 

8. Repeat step 7 now for each additional remotes to be programmed including any existing
    remotes.

 

9. Remove key from ignition.

 

10. Install the "MALL PGM" fuse back into the fuse panel and test remote(s).


1997 - 1999 Saturn SC
1997 - 1999 Saturn SL
1997 - 1999 Saturn SW

 

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.  

 

1.      Insert keys in ignition and leave in the OFF position.  

 

2.      Locate the Data Port.



3.     Make sure there are metal contact pins in terminals 8 and 4. Connect 8 and 4 with a suitable jumper wire (leave the jumper wires connected throughout the programming procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond by locking then unlocking the doors to signify entering of the programming mode.  

 

4.      Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. Up to about 30 seconds, the vehicle will respond by locking then unlocking the doors. Release the buttons on the transmitter.  

 

5.    Within one minute, repeat the previous step on the remaining transmitter (if any – including your old one).  

 

6.      Remove jumper wire applied to the Data Port (disconnect 8 and 4).





Customer Reviews of Our Service
Please Note: Reviews about self-programming do not indicate the product above is self-programmable. Please inquire about each product.
Back up
1