1993 - 1996 GM 3 Button Keyless Entry Remote - ABO0103T (Olds logo)

Your price: $20.99

In stock
1993 - 1996 GM 3 Button Keyless Entry Remote

1993 - 1996 GM 3 Button Keyless Entry Remote - ABO0103T (Olds logo)


Fits:

1993 - 1996 Buick Century
1993 - 1996 Buick Regal
1993 - 1995 Buick Roadmaster
1993 - 1995 Buick Skylark
1993 - 1995 Chevrolet Caprice
1993 - 1996 Oldsmobile Achieva

Product Specs and Programming Information
SKU 7107
FCC Number ABO0103T
OE Part # #10063534, #25602667, #25602668, #25602669
Support Your purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee! If you are not 100% satisfied, you may return the product within thirty days of receipt for a refund. Please see our return policy for further info.
Programming Information This remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab. NOTE: When looking under the 'Programming Instructions' tab please look for your specific model as the programming instructions vary.
Product Condition Refurbished
Programming Instructions

1993 - 1996 Oldsmobile Achieva

1993 - 1995 Buick Skylark

1993 - 1996 Buick Century

1993 - 1995 Buick Roadmaster

.  Locate the programming connector located in the LH trunk. Trim may
     have to be pulled back to access programming connector. ( Connector
     has wires leading up to it and it is not connected to anything.)

2.  Jump programming connector terminals. Leave terminals jumped
     unitl step 6.

3.  System should now lock and unlock doors to indicate 
      programming mode has been entered. 

4.  Press any button on keyless remote once.
     System should now lock and unlock doors, indicating successful 
     programming of keyless remote.  

5.  Repeat step 4 for additional remote or other existing keyless remote.
     
     NOTE: A maximum of only two Keyless Remotes can be programmed.

6.  Remove programming connector jumper wire to exit programming mode.

7.  Test remote(s).


1993 - 1996 Buick Regal

Note: Existing keyless remotes will be erased with this procedure.
          Existing working remotes will have to reprogrammed also.

1. Locate the programming connector wire located in the RH trunk area.
    You may have to pull back right side trunk trim on trunk wall to locate 
    the single black/white wire.

2. The programming connector wire should have one termial in the plastic
    connector on end of black/white wire. Ground the terminal in the connector
    to  a nearby bolt or trunk latch.
    Leave connector wire connected to ground through out procedure.

3. System will now lock and unlock doors automatically to indicate 
    programming mode has been activated.

4. Press any button on keyless remote. System will respond by locking 
    and unlocking doors one time to indicate successful programming.

5. Repeat step 4 for to program any additonal keyless remotes including
    and existing keyless remotes. Do not remove ground wire between
    programming of keyless remotes.

6. Disconnect programming connector wire from ground to exit programming
    mode.

7. Test keyless remote(s).



1993 - 1995 Chevrolet Caprice

1. Access programming connector in LH side of trunk (drivers side). Programming connector will be close to the tail light, it will not be connected to anything and should be one black and one white wire. It will have a plastic connector on the end of it with two holes in it or ports.


2. Jump programming connector using a suitable jumper wire. Jumping the connector means to use a wire or paperclip bent in the shape of a U to make a connection between the two ports. Be sure you are making contact with the metal inside both ports.


3. System should now lock and unlock doors and activate trunk release to indicate successful entry into programming mode.

 
4. Press any button on remote one time. System should now lock and unlock doors and activate trunk release to indicate successful programming of remote.

 
5. Repeat step 4. for each additional remote including working ones.


6. To exit programming mode remove jumper wire and test all remotes.



Copyright © 2019-present Replacemyremote.com All rights reserved.