1996 - 2001 Cadillac 4 Button Keyless Entry Remote w/ Gas - AB01602T

Your price: $52.99

In stock
1996 - 2001 Cadillac 4 Button Keyless Entry Remote w/ Gas - AB01602T

1996 - 2001 Cadillac 4 Button Keyless Entry Remote w/ Gas - AB01602T

Fits:

1996 - 2001 Cadillac Catera
1996 - 1997 Cadillac DeVille
1996 - 1997 Cadillac Eldorado
1996 - 1997 Cadillac Seville

 

Product Specs and Programming Information
SKU 7248
FCC Number AB01602T
OE Part # 16183016 16196066
Support Your purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee! If you are not 100% satisfied, you may return the product within thirty days of receipt for a refund. Please see our return policy for further info.
Programming Information Please Check if your vehicle has Self-Programming instructions by Clicking the Tab Above. "Programming Instructions"
Product Condition Refurbished
Programming Instructions

1996 - 2001 Cadillac Catera's are Not Self-Programmable and will require an Automotive Locksmith to Program.

1996 - 1997 Cadillac Eldorado Programming Instructions:

  Use these instuctions if your ElDorado has an  Analog Instrument Cluster 
 

1.   Press OFF and WARM buttons on  Climate Control Panel (CCP) simultaneously.   
      (Instrument Panel Cluster (IPC) will light all telltales, then go blank) System is now in diagnostic mode. 
       Press PASSENGER COOLER button until “RFA” is displayed, then press FAN UP.

      If   “RFA DATA” is displayed, press FAN DOWN.

      If   “RFA OVERRIDE” is displayed, press FAN UP.

 

2.   If  “RFA 500 NO OVERRIDE” is displayed, press FAN DOWN.

      If  “RFA 501 PROGRAM FOB #1” is displayed, Press FAN UP.

 

3.   IPC will show “0” on right side of Driver Information Center (DIC) display.

      Press warmer button on climate control unit until “99” is displayed.

 

4.   Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
      second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
      programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
      step 2.

 

5.   To program a second remote, press FAN DOWN button until  “RFA 502 PROGRAM FOB #2” is displayed, then press 
      FAN UP.  Repeat step 4.

 To exit system, press AUTO, MODE UP, MODE DOWN, or RESET.  

  Use these instructions if your ElDorado has a  Digital Instrument Cluster

  

1.   Press OFF and WARM buttons on Climate Control Center (CCC) simultaneously. Instrument Panel Cluster (IPC) will
       light all telltales, go blank then  enter DIAGNOSTIC
 MODE. Press FAN DOW button to scroll through system until
       “RFA” is displayed, then press FAN UP button. Press FAN DOWN button until “RFA OVERRIDE” is displayed, then
        press FAN UP button. When  “NO OVRD RF 500” is displayed, then press FAN UP button.

 

2.   When “PGM FOBL 501” is displayed, press WARM button and “99” will be displayed in left upper corner of IPC just
      below odometer. System is now ready to program remote.

 

3.   Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
      second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
      programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
      step 2.)

 

4.  To program second remote, pres FAN UP button until “PGM FOB2 502” is displayed, then follow steps 2 and 3 to
      program second remote.

 To exit system, press RECIRC or RESET buttons.

1996 - 1996 Cadillac Seville Programming Instructions:

 Use these instuctions if your SeVille has an  Analog Instrument Cluster 
 

1.   Press OFF and WARM buttons on  Climate Control Panel (CCP) simultaneously.   
      (Instrument Panel Cluster (IPC) will light all telltales, then go blank) System is now in diagnostic mode. 
       Press PASSENGER COOLER button until “RFA” is displayed, then press FAN UP.

      If   “RFA DATA” is displayed, press FAN DOWN.

      If   “RFA OVERRIDE” is displayed, press FAN UP.

 

2.   If  “RFA 500 NO OVERRIDE” is displayed, press FAN DOWN.

      If  “RFA 501 PROGRAM FOB #1” is displayed, Press FAN UP.

 

3.   IPC will show “0” on right side of Driver Information Center (DIC) display.

      Press warmer button on climate control unit until “99” is displayed.

 

4.   Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
      second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
      programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
      step 2.

 

5.   To program a second remote, press FAN DOWN button until  “RFA 502 PROGRAM FOB #2” is displayed, then press 
      FAN UP.  Repeat step 4.

 

      To exit system, press AUTO, MODE UP, MODE DOWN, or RESET.  

   Use these instructions if your SeVille has a  Digital Instrument Cluster  


1.   Press OFF and WARM buttons on Climate Control Center (CCC) simultaneously. Instrument Panel Cluster (IPC) will
       light all telltales, go blank then  enter DIAGNOSTIC
 MODE. Press FAN DOW button to scroll through system until
       “RFA” is displayed, then press FAN UP button. Press FAN DOWN button until “RFA OVERRIDE” is displayed, then
        press FAN UP button. When  “NO OVRD RF 500” is displayed, then press FAN UP button.

 

2.   When “PGM FOBL 501” is displayed, press WARM button and “99” will be displayed in left upper corner of IPC just
      below odometer. System is now ready to program remote.

 

3.   Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
      second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
      programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
      step 2.)

 

4.  To program second remote, pres FAN UP button until “PGM FOB2 502” is displayed, then follow steps 2 and 3 to
      program second remote.

 

     To exit system, press RECIRC or RESET buttons.

 

Copyright © 2019-present Replacemyremote.com All rights reserved.