1998 - 2002 Toyota 2 Button Keyless Entry Remote - BAB237131-022 - Gray case

Dealer price: $114.21

Your price: $73.00

You Save: $41.21

That's 36.08% OFF dealer price!

In stock
1998 - 2002 Toyota 2 Button Keyless Entry Remote - BAB237131-022 - Gray case

1998 - 2002 Toyota 2 Button Keyless Entry Remote - BAB237131-022 - Gray case

This original remote has been discontinued and the only option for replacing it is SKU: 2726. There may be cosmetic differences, such as the case shape, FCC ID, OE part number, brand logo or button icons, but these differences are all strictly cosmetic. This part comes from the same manufacturer, and is functionally identical to the original.

If the discontinued remote is currently out of stock, you will be sent the Replacement OE remote in its place.

Fits:

1998 - 1999 Toyota 4Runner
1998 - 1999 Toyota Avalon
1998 - 1999 Toyota Camry
1998 - 1999 Toyota Celica
1998 - 2002 Toyota Corolla
1998 Toyota Paseo
1998 - 2000 Toyota Rav4
1998 - 2000 Toyota Sienna
1999 - 2001 Toyota Solara
1998 Toyota Supra
1998 Toyota T100
1998 - 2001 Toyota Tacoma
1998 Toyota Tercel
2000 - 2002 Toyota Tundra

Product Specs and Programming Information
SKU 2727
FCC Number BAB237131-022
OE Part # 08191-00871
Support Your purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee! If you are not 100% satisfied, you may return the product within thirty days of receipt for a refund. Please see our return policy for further info.
Programming Information This remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab.
Product Condition Refurbished
Programming Instructions

FOR VEHICLES WITH DEALER INSTALLED KEYLESS ENTRY USE THIS PROCEDURE


1998 4Runner

1998 - 1999 Celica

1998 - 2002 Corolla 

1998 Paseo                              

1998 - 2000 Rav4 

1998 Supra  

1998 T100

1998 - 2001 Tacoma 

1998 Tercel

2000 - 2002 Tundra 

 

Obtain all remote transmitters for this vehicle.

1. Insert key into ignition and turn ignition switch to ON position.

2. Locate the ECU (Engine Control Unit) and press and hold the ECU PROGRAMMING SWITCH for 3 seconds (refer to diagram for location). The ECU will be located under one of the front two seats, the trunk, or under the dashboard on the drivers side. You will see the STATUS MONITOR LED turn on for 5 seconds. Vehicle is now in programming mode.

3. Press and release either the top or bottom button on the remote. The STATUS MONITOR LED will turn off. A chirp will be heard as well as one flash of the exterior lights.

4. Turn off the ignition. Programming is now complete, test remotes for proper programming.


FOR VEHICLES WITH FACTORY INSTALLED KEYLESS ENTRY USE THIS PROCEDURE


1999 4Runner

1999 - 2000 Sienna

1999 - 2001 Solara

1998 - 1999 Avalon


Obtain all remote transmitters for this vehicle.

1. Start with key out of the ignition, open and unlock drivers door and be sure all other doors and trunk are closed.


2. Insert key into ignition (Do not turn) and pull it out.


3. Perform these steps within 40 seconds. A. Using the power door lock rocker switch on drivers door perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1 unlock.).


4. Close, then open drivers door.


5. Perform these steps within 40 seconds. A. Using the power door lock rocker switch on drivers door perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1 unlock.) B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Just shy of starting car, Do NOT Start) then back to OFF. D. Turn the ignition to ON (Just shy of starting car, Do NOT Start)) then back to OFF. E. Remove the key from the ignition.


6. Within 3 seconds the power door locks should cycle automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point, if they do cycle then continue to step 7.


7. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remote simultaneously for 1 second. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks should cycle once indicating successful programming. If the door locks don't cycle or cycle twice, repeat steps A and B, your remote has not been accepted. C. Repeat steps A and B in step 7 for each new transmitter.

8. Close drivers door.

9. Test all remotes.

 

1998 - 1999 Camry

 

Obtain all remote transmitters for this vehicle.

1. With the key out of the ignition remove the mirror adjustment switch from door and unplug harness. Jump pin 2 to pin 10 on the mirror adjustment harness. When done correctly vehicle will automatically cycle the door locks to LOCK and then UNLOCK.

2. Press any button on first remote to be programmed. Door locks should automatically cycle again to show acceptance of remote.

3. Repeat step 2 for any remaining remotes to be programmed.

4. Once all remotes are programmed remove jumper wire and replace mirror adjustment switch. Test all remotes to ensure proper programming.

 

1998 Sienna


Obtain all remote transmitters for this vehicle.

1. Locate the Wireless Door Lock ECU. It is located towards the front of the center console. With the key out of the ignition and the ECU still connected jump cavity 9 to cavity 1. Cavity 9 will not have a wire going into it while cavity 1 will have a wire going into it. Cavities 2, 3, 6, 7, 9, 12, and 13 will be empty while cavities 1, 4, 5, 8, 10, 11, 14, and 15 will have wires entering the cavities. Ensure when jumping pin 9 to 1 that you make contact with the metal pins in the cavities. Leave jumper wire connected throughout the procedure.

2. Once jumped properly the power door locks will cycle to lock and then unlock. Once vehicle automatically cycles the door locks then vehicle is in programming mode.

3. Press any button on the first remote to be programmed. Vehicle will confirm recognition by once again cycling the door locks.

4. Repeat step 3 for any additional remotes to be programmed to the vehicle.

5. Remove jumper wire from ECU and test remotes to ensure proper programming.

msrp $114.21
Copyright © 2019-present Replacemyremote.com All rights reserved.