2014 - 2018 OEM Cadillac Smart Remote w/ Trunk - Emergency key included - 315Mhz - HYQ2AB

Dealer price: $349.96

Your price: $118.00

You Save: $231.96

That's 66.28% OFF dealer price!

In stock
2014 - 2018 OEM Cadillac Smart Remote w/ Trunk - Emergency key included - 315Mhz - HYQ2AB

2014 - 2018 OEM Cadillac Smart Remote w/ Trunk - Emergency key included - 315Mhz - HYQ2AB

Ekey: 7275

Fits:

2015 - 2018 Cadillac ATS
2014 - 2018 Cadillac CTS
2015 - 2018 Cadillac XTS

Product Specs and Programming Information
SKU 1864
FCC Number HYQ2AB
OE Part # N13580811
Support Your purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee! If you are not 100% satisfied with your product for any reason, you may return the product within 180 days of ordering for a replacement. Please see our return policy for further inf
Programming Information This remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab.
Product Condition Refurbished
Programming Instructions

Programming with a Recognized
Transmitter

A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be off and all transmitters, both currently recognized and new, must be with you.

1. Remove the vehicle key from the recognized transmitter.

2. Place the recognized transmitter(s) in the cupholder.

3. Remove the key lock cylinder cap on the driver door handle. See Door Locks 0 37. Insert the vehicle key into the key lock cylinder on the driver door handle, then turn the key counter clockwise to the unlock position five times within10 seconds.
The Driver Information Center(DIC) displays READY FORREMOTE #2, 3, 4, ETC.

4. Place the new transmitter into the transmitter pocket. The center console storage area will need to be opened and the rubber mat needs to be removed to access the transmitter pocket.

5. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.

6. Remove the transmitter from the transmitter pocket and press K or Q on the transmitter.

To program additional transmitters, repeat Steps 4–6.When all additional transmittersare programmed, press and hold the ENGINE START/STOP button for approximately12 seconds to exit programming mode.

7. Return the vehicle key back into the transmitter.

 

 

 


Programming without a
Recognized Transmitter

If there are no currently recognized transmitters available, follow this procedure to program up to eight transmitters. This feature is not available in Canada. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all transmitters to be programmed must be with you.

1. Remove the vehicle key from the transmitter.

2. Remove the key lock cylinder cap on the driver door handle. See Door Locks 0 37. Insert
the vehicle key into the key lock cylinder on the driver door handle, then turn the key counter clockwise to the unlock position five times within10 seconds. The Driver Information Center(DIC) displays REMOTELEARN PENDING,PLEASE WAIT.

3. Wait for 10 minutes until the DIC displays PRESS ENGINESTART BUTTON TO LEARN and then press the ENGINESTART/STOP button. The DIC display will again show REMOTE LEARNPENDING, PLEASE WAIT.

4. Repeat Step 3 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show READY FOR REMOTE# 1.

5. Place the new transmitter in
the transmitter pocket. The center console storage area will need to be opened and the rubber mat needs to be removed to access the transmitter pocket.

6. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.

7. Remove the transmitter from the transmitter pocket and press K or Q on the transmitter.

To program additional transmitters, repeat Steps 5–7.

When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately

12 seconds to exit programming mode.

8. Return the vehicle key back into the transmitter.

msrp $349.96
Copyright © 2018-present Replacemyremote.com All rights reserved.