2015 - 2016 Cadillac Escalade 6 Button Smart Remote - Emergency key included - HYQ2AB

Dealer price: $280.98

Your price: $128.00

You Save: $152.98

That's 54.45% OFF dealer price!

In stock
2015 - 2016 Cadillac Escalade 6 Button Smart Remote - Emergency key included - HYQ2AB

2015 - 2016 Cadillac Escalade 6 Button Smart Remote - Emergency key included - HYQ2AB

Ekey: 7275

Fits:

2015 - 2016 Cadillac Escalade

 

*IMPORTANT* For 2017 Escalade you MUST verify Mhz or FCC ID to ensure you are purchasing the correct item. 

Product Specs and Programming Information
SKU 6769
FCC Number HYQ2AB
OE Part # 13580812
Support Your purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee! If you are not 100% satisfied, you may return the product within thirty days of receipt for a refund. Please see our return policy for further info.
Programming Information This remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab.
Product Condition Refurbished
Programming Instructions

Programming With A Recognized Transmitter

A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be off and all transmitters, both currently recognized and new, must be with you.

1. Remove the key from the recognized transmitter.

2. Place the recognized transmitter(s) in the cupholder or passenger seat.

3. Remove the key lock cylinder cap on the driver door handle. See Door Locks on page 2-10. Insert the vehicle key into the key lock cylinder on the driver door handle; then turn the key counterclockwise, to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays READY FOR REMOTE #2, 3, 4, ETC.

4. Place the new transmitter in the transmitter pocket/insert. The transmitter pocket/insert next to the center console storage area.

5. Press the ENGINE START/ STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.

6. Open the center console storage area and the storage tray.

7. Remove the transmitter from the transmitter pocket/insert and press K or Q on the transmitter. To program additional transmitters, repeat Steps 3–5. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode.

8. Return the key back into the transmitter.

 

Programming Without A Recognized Transmitter

If there are no currently recognized transmitters available, follow this procedure to program up to eight transmitters. This feature is not available in Canada. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all transmitters to be programmed must be with you.

1. Remove the vehicle key from the transmitter.

2. Remove the key lock cylinder cap on the driver door handle. See Door Locks on page 2-10. Insert the vehicle key into the key lock cylinder on the driver door handle; then turn the key counterclockwise, to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays REMOTE LEARN PENDING, PLEASE WAIT.

3. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/ STOP button. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.

4. Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show READY FOR REMOTE # 1.

5. Place the new transmitter in the transmitter pocket/insert. The transmitter pocket/insert is next to the center console storage area. The storage area will need to be opened to access the transmitter pocket/insert.

6. Press the ENGINE START/ STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.

7. Remove the transmitter from the transmitter pocket/insert and press K or Q on the transmitter. To program additional transmitters, repeat Steps 4–6. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode.

8. Return the key back into the transmitter.

msrp $280.98
Copyright © 2018-present Replacemyremote.com All rights reserved.