2017 - 2019 Chevrolet 4 Button Smart Remote w/ Remote Start - Emergency Key Included - 433Mhz - HYQ4EA

2017 - 2019 Chevrolet 4 Button Smart Remote w/ Remote Start - Emergency Key Included - 433Mhz - HYQ4EA
Dealer Price $248.95 Your Price $119.99 You save $128.96 That's 51.8% OFF dealer price!
Availability: In stock
SKU
7520
2017 - 2019 Chevrolet 4 Button Smart Remote w/ Remote Start - Emergency Key Included - 433Mhz - HYQ4EA
EKey: 7403
Fits:
2017 - 2018 Chevrolet Volt
2017 - 2019 Chevrolet Cruze
2018 - 2019 Chevrolet Traverse

180 Day Satisfaction Guarantee!

If you are not 100% satisfied with your product for any reason, you may return the product within 180 days of ordering for a replacement. Please see our return policy for further information.

 

More Information
SKU7520
FCC NumberHYQ4EA
OE Part #13585728
SupportYour purchase gives you 100% free e-mail and phone technical support from our expert staff.
Programming InformationThis remote comes with self programming instructions which you can view under the "Programming Instructions" tab above or in your owner's manual under 'Keys, Doors, and Windows'.
Product ConditionRefurbished
Programming Instructions

Programming Transmitters to the Vehicle

Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed. The vehicle can be reprogrammed so that lost or stolen transmitters no longer work. Any remaining transmitters will need to be reprogrammed. Each vehicle can have up to eight transmitters matched to it.

Programming with Recognized Transmitters

A new transmitter can be programmed to the vehicle when there are TWO recognized transmitters. To program, the vehicle must be off and all of the transmitters, both currently recognized and new, must be with you.

1. Place the two recognized keys in the front cupholder.

2. Remove the key lock cylinder cap on the driver door handle. See Door Locks pg. 44. Insert the vehicle key of the new transmitter into the key lock cylinder on the outside of the driver door and turn the key to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays READY FOR REMOTE #2, 3, 4 or 5 etc.

3. Remove the recognized key and place the new transmitter into the front cupholder.

4. Press ENGINE START/STOP. When the transmitter is learned, the DIC will show that it is ready to program the next transmitter.

5. Remove the transmitter from the front cupholder and press UNLOCK or LOCK on the transmitter.

To program additional transmitters, repeat Steps 3–5. When all additional transmitters are programmed, press and hold ENGINE START/STOP for 12 seconds to exit programming mode.

Programming without Recognized Transmitters

If TWO currently recognized transmitters are not available, follow this procedure to program up to eight transmitters. This feature is not available in Canada. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all of the transmitters you wish to program must be with you.

1. Remove the key lock cylinder cap on the driver door handle. See Door Locks pg. 44. Insert the vehicle key of the transmitter into the key lock cylinder on the outside of the driver door and turn the key to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays REMOTE LEARN PENDING, PLEASE WAIT.

2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC displays will again show REMOTE LEARN PENDING, PLEASE WAIT.

3. Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show READY FOR REMOTE # 1.

4. Place the transmitter in the front cupholder.

5. Press ENGINE START/STOP. When the transmitter is learned the DIC will show that it is ready to program the next transmitter.

6. Remove the transmitter from the front cupholder and press UNLOCK or LOCK on the transmitter. To program additional transmitters, repeat Steps 4–6. When all additional transmitters are programmed, press and hold ENGINE START/STOP for 12 seconds to exit programming mode.

7. Return the vehicle key back into the transmitter.

msrp248.95