Enter Your Email Address For

An Instant $5.00 OFF Coupon!

Find My Remote or Key Now!

1991 - 1995 Buick 3 Button Keyless Entry Remote Fob - ABO0302T

Availability: In stock

Dealer Price: $126.25

$29.99

You Save: $96.26

That's 76.25% OFF Dealer price!

this link

2-Years Extended Warranty Plan

Replace My Remote offers an optional Extended 2-Year warranty on all remote and remote key products for Only $7.99. You can view the full terms and coverage of the warranty by clicking the  blue "View All Terms" link. Simply check the "Warranty" check box to add the 2 year extended warranty to your product.

This is an authentic factory/OEM device meant to operate your specific vehicle.

76.25%
off

1991 - 1995 Buick 3 Button Keyless Entry Remote Fob - ABO0302T

More Views

1991 - 1995 Buick 3 Button Keyless Entry Remote Fob - ABO0302T

Fits:

1991 - 1995 Buick Park Avenue
1991 - 1993 Buick Century
1992 - 1995 Buick LeSabre

Additional Information

SKU 948
FCC Number ABO0302T
OE Part # 25602667
Support Your purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee! If you are not 100% satisfied with your product for any reason, you may return the product within 180 days of ordering for a replacement. Please see our return policy for further info
Programming Information MOST models come with self programming instructions. You can view them under the 'Programming Instructions' tab. All other models will need an automotive locksmith to come out and program the unit in for you. NOTE: When looking under the 'Programming Instructions' tab please look for your specific model AND YEAR as the programming instructions vary.
Product Condition Refurbished
Manufacturer's Suggested Retail Price $126.25

1991-1993 Buick park avenue

1992 - 1993 Buick leSabre


Obtain all remote transmitters for this vehicle.

 

obd1-colored-a-m.jpg

 

1.     Locate the Data Link Connector (DLC) underneath the driver's side dashboard.
Please refer to the diagram above to determine the G and A cavity. The

letters will not appear on the connector. They are on the diagram for 

ease of reference.


2.     Connect cavity G with cavity A using a fused jumper wire.
Your vehicle will respond by locking and unlocking the door locks within 2 seconds.
 

3.     Press the UNLOCK button once on first remote to be programmed.
Locks will lock and unlock verifying remote was programmed.
 

4.     Press the UNLOCK button on second remote to be programmed if applicable.
Locks will lock and unlock to verify remote was programmed.
 

5.     Remove jumper wire and test remote(s)


1994-1995 Buick park avenue

1994 - 1995 Buick leSabre


 

1.   Insert key in ignition and leave in the OFF position

 

2.    Locate the Data Link Port. It is located under dash drivers side. Be sure you know
     
which pins are 8 and 4.   

        (Note port is wider at top) Your OBDII port will not
              have numbers, use this diagram for reference.
 

    

3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a 
        suitable jumper wire (leave the jumper
wire 
connected throughout the programming
        procedure).
Make sure you know which terminals are 8 and 4.

4.    Close doors.

5.   Turn ignition to the ON position (as far as you can go without cranking the engine).
      Doors will lock. 

 

6.      Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to
       be programmed. After about 15 seconds, the
vehicle will respond by locking and
       unlocking the doors. 
Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitters to be
      
programmed.

8.    Remove jumper wire applied to th OBDII Port.

9.    A maximum of two keyless remotes can be programmed.


1992 Buick Century

1. Open trunk and locate the Programming Connector by the left side wheel well. Programming Connector may be behind the trim or carpet and will not be connected to anything. It will be a plastic connector with two wires running from it.

 

2. Ensure that there are two metal pins or terminals in the connector. Jump one pin to the other. This can be done with a jumper wire or a paper clip bent. Once jumped properly the door locks will cycle to lock then unlock.

 

3. Vehicle is now in programming mode. Press unlock on the remote once. When accepted the door locks will cycle again to lock then unlock.

 

4. Repeat step 3 when programming a second remote.

 

5. Programming is now complete. Remove jumper wire from Programming Connector and test remotes to ensure proper programming.


1993 Buick Century

 

1.  Locate the green programming connector located in the LH trunk. Trim may
     have to be pulled back to access programming connector. ( Connector
     has wires leading up to it and it is not connected to anything.)

 

2.  Jump programming connector terminals.

 

3.  System should now lock and unlock doors and trunk lid to indicate 
      programming mode has been entered. Trunk lid must have activated
      before proceeding.

 

4.  Press any button on keyless remote once.
     System should now lock and unlock doors and trunk lid, indicating 
     successful programming of keyless remote. Trunk lid must have
     activated before proceeding. 

 

5.  Repeat step 4 for additional remote or other existing keyless remote.
    
     NOTE: A maximum of only two Keyless Remotes can be programmed.

 

6.  Remove programming connector jumper wire to exit programming mode.

 

7.  Test remote(s).





Customer Reviews of Our Service
Please Note: Reviews about self-programming do not indicate the product above is self-programmable. Please inquire about each product.
Back up
1
Get Your Coupon Now for
3% Off Your Purchase!
Receive a 3% Off Coupon Code in Your email within just minutes by simply signing up for our Newsletter. Then, just apply the coupon code at checkout for Your Savings.