1996 - 2004 OEM Toyota 3 Button Keyless Entry Remote Fob - BAB237131-056

1996 - 2004 OEM Toyota 3 Button Keyless Entry Remote Fob - BAB237131-056

1996 - 2004 OEM Toyota 3 Button Keyless Entry Remote Fob - BAB237131-056

1996 - 2004 OEM Toyota 3 Button Keyless Entry Remote Fob - BAB237131-056

Dealer Price $172.29 Your Price $79.99 You save $92.3 That's 53.57% OFF dealer price!
Availability: In stock
SKU
2732

1996 - 2004 OEM Toyota 3 Button Keyless Entry Remote Fob - BAB237131-056


Fits:

1996 - 1997 Toyota 4Runner
2000 - 2002 Toyota Avalon
2000 - 2001 Toyota Camry (Dealer installed)
1998 - 2002 Toyota Corolla (Dealer installed)
2000 - 2003 Toyota Celica (Dealer installed)
2000 - 2003 Toyota Echo
2000 - 2004 Toyota MR2
2000 - 2001 Toyota Sienna
2002 - 2004 Toyota Tacoma (Dealer installed)
1998 - 2006 Toyota Tundra

More Information
SKU2732
FCC NumberBAB237131-056
OE Part #08191-00922, 08191-00921, 08191-00920
SupportYour purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee!If you are not 100% satisfied, you may return the product within thirty days of receipt for a refund. Please see our return policy for further info.
Programming InformationThis remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab.
Product ConditionRefurbished
Programming Instructions
1. 1996-1997 4Runner,  1998- 2002 Corolla,  2000-2002 Tundra


Obtain all remote transmitters for this vehicle.

1. Insert key into ignition and turn ignition switch to ON position.

2. Locate the ECU (Engine Control Unit) and press and hold the ECU PROGRAMMING button for 3 seconds (refer to diagram for location). The ECU will be located under one of the front two seats, the trunk, or under the dashboard on the drivers side. You will need a small pointy object like a pen to depress the ECU button. After pressing the ECU button for three seconds, you will see the STATUS MONITOR LED turn on for 5 seconds. Vehicle is now in programming mode.

3. Press and release either the top or bottom button on the remote (If you purchased a four button duplicate remote simply press the lock or unlock button since the other two buttons will not be used). The STATUS MONITOR LED will turn off. A chirp will be heard as well as one flash of the exterior lights.

4. Turn off the ignition. Programming is now complete, test remotes for proper programming.

 

 

2. 2000-2002 Avalon,  2000-2001 Camry, 2000-2001 Sienna

1.  Start with key out of the ignition, driver door is open (all others closed), and driver 
         door is unlocked.

    2.  Insert key into the ignition (don’t turn it) and pull it out

    3.  Perform these steps within 40 seconds:

a. Using the power lock switch on the driver’s door, perform 5 lock/unlock cycles 
    starting with lock. 
Use an even pace and try to go about one cycle per second. 
    (1 cycle = 1 lock and 1 unlock)

b. Close, then open driver’s door.

     4.  Perform these steps within 40 seconds:

a. Using the power lock switch on the driver’s door, perform 5 lock/unlock cycles
    starting with lock. Use an even pace and try to go about one cycle per second.
    (1 cycle = 1 lock and 1unlock) 

b. Insert the key in the ignition cylinder.

c. Turn the ignition to ON (as far as you can without cranking the engine) 
    then back to OFF     

d. Remove the key from the ignition.

     5.  Within 3 seconds, the power door locks should cycle automatically indicating
          successful entry into programming mode. 
         
Return to step 1 if the locks do not cycle at this point.

     6.  Perform these steps within 40 seconds:

a. Press the lock and unlock buttons on the transmitter simultaneously for 1
    second.

b. Immediately after letting go of the lock and unlock buttons, hit the lock button
    by itself and  hold for 2 seconds. Within 3 seconds, the door locks should cycle
    once indicating successful programming. If the door locks don’t cycle, or cycle
    twice, repeat steps a and b-your remote has not been accepted.

c. Repeat steps a and b in step 6 for each new transmitter. 

    7.  Close door.
    
     8. Grab Key and Remote, step out of car and test remote(s).

      Tip: It has been reported that some Avalons require trunk to be open during programming.



3. 2000-2003 Celica,  2000-2003 Echo,  2000-2004 MR2 Spyder,  2002-2004 Tacoma, 2003-2006 Tundra

1. Start with the key out of the ignition, drivers door is open all others closed and 
    drivers door is unlocked.

2. Perform these steps within 5 seconds.
    A. Insert the key into the ignition(Do NOT Turn) Pull key out.
    B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
    A. Close then open the drivers door.
    B. Close then open the drivers door.
    C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
    A. Close then open the drivers door.
    B. Close then open the drivers door.
    C. Insert the key into ignition and leave it in ignition.
    D. Close the drivers door.
    E. Turn the ignition to ON (Do NOT Start) then back to OFF.
    F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically
    indicating successful entry into programming mode.
    Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
    B. Immediately after letting go of the lock and unlock buttons,
        Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
        locks should lock and then unlock once indicating successful programming. If
        the door locks cycle twice, repeat steps A and B in step 6 as the remote was
        not accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

msrp172.29