1999 - 2003 Dodge Ram Van 2 Button Keyless Entry Remote Fob - GQ43VT9T

1999 - 2003 Dodge Ram Van 2 Button Keyless Entry Remote Fob - GQ43VT9T

1999 - 2003 Dodge Ram Van 2 Button Keyless Entry Remote Fob - GQ43VT9T

1999 - 2003 Dodge Ram Van 2 Button Keyless Entry Remote Fob - GQ43VT9T
Dealer Price $126.25 Your Price $37.99 You save $88.26 That's 69.91% OFF dealer price!
Availability: In stock
SKU
587

  1999 - 2003 Dodge Ram Van 2 Button Keyless Entry Remote Fob - GQ43VT9T

Fits:

1999 - 2003 Dodge Ram Van

More Information
SKU587
FCC NumberGQ43VT9T
OE Part #56045191AA, 56045191AB, 56045191AC, 56045191AD, 56045191AE, 56045191AF
SupportYour purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee!If you are not 100% satisfied, you may return the product within thirty days of receipt for a refund. Please see our return policy for further info.
Programming InformationThis remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab.
Product ConditionRefurbished
Programming Instructions

1999 - 2002 Dodge Ram Van:


dlc-port-1-16.jpg

 

 

Obtain all remote transmitters for this vehicle.

1. Locate the Data Link Connector (DLC). It will be under the dash on the drivers side. Use the diagram above to identify pins 1 and 4. Notice that the DLC connector is tapered. You can use this to help identify the proper pins. Using a suitable jumper wire jump pin 1 to pin 4. Ensure that there are metal connector ends in the cavities that are referenced in this procedure. Once the jumper wire is installed it needs to remain there throughout this process until instructed to remove.


2. Insert key into the ignition and turn the ignition switch to the ON position. (ON is turning ignition switch as far as you can without cranking the engine)


3. If jumper wire is installed properly, once ignition is ON the door locks will Lock and Unlock once.


4. Now press any button on the first remote to be programmed. To show that the signal from remote is recognized the door locks will cycle again (Lock and Unlock) and the rear window will release if equipped. This step must be repeated for all remaining remotes to be programmed to vehicle.


5. Once all remotes are programmed remove jumper wire and turn ignition to OFF. Test all remotes to ensure proper programming.


2003 Dodge Ram Van:

 

YOU MUST HAVE A WORKING REMOTE FOR THIS PROCEDURE TO WORK. IF YOU DON'T HAVE A WORKING REMOTE THEN YOU MUST HAVE A REMOTE PROGRAMMED BY A LOCKSMITH USING DIAGNOSTIC EQUIPMENT.

 

PLEASE READ ENTIRE PROCEDURE BEFORE PERFORMING. SOME VEHICLES MAY USE ONE OF TWO PROCEDURES. IF PROCEDURE 1. DOES NOT WORK THEN PLEASE USE PROCEDURE 2.

 

 

 

Programming procedure #1.

 

Obtain all remote transmitters for this vehicle.

 


 

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

 


 

2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.

 


 

3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.

 


 

4. Press any button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.

 


 

5. Within 30 seconds of completiong step 4. press any button on the next remote. Repeat step 5. for all additional remotes including working remotes.

 


 

6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

 

 

 

Programming Procedure #2

 

Obtain all remote transmitters for this vehicle.

 


 

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

 


 

2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.

 


 

3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.

 


 

4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.

 


 

5. Within 30 seconds of completing step 4. press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.

 


 

6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.


msrp126.25