2001 - 2004 NEW Replacement GM 3 Button Keyless Entry Remote Fob - KOBLEAR1XT

2001 - 2002 Chevrolet Silverado
2001 - 2004 Chevrolet Suburban
2001 - 2004 Chevrolet Tahoe

You must have all remotes including working ones when performing this procedure.

1. Close all doors.

2. Insert key into the ignition.

3. Press and hold the power UNLOCK button on driver's side door panel. Do not release until instructed to do so in step 5.

4. Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just shy of starting your vehicle, OFF is the position where you can remove your key)

5. Release the power unlock button on the driver's side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock button then the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If the vehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotes must be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key too quick, too slow, there's a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.

6. Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30 seconds.

7. NOW repeat step 6. for all additional remotes including working ones.

8. After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.

9. Turn ignition to OFF, remove key and test all remotes.

 

2002 Chevrolet Avalanche.

1. Close all doors

2. Insert key into ignition

3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.

5. Turn the ignition to the ON position (as far as you can go without starting the engine.)

6. Turn the ignition to the OFF position.

7. Turn the ignition to the ON position (as far as you can go without starting the engine.)

8. Turn the ignition to the OFF position.

9. Release the power UNLOCK button on the door panel. The vehicle should respond by door locks locking and unlocking automatically. (If locks do not cycle after you let go, not before you let go of the unlock button, then the vehicle has not entered programming mode and you must start procedure over. Remove key from ignition, open drivers door and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).

12. Turn the ignition to the ON position to exit the programming mode.

 

2002 Cadillac Escalade ONLY

1. Close all doors.

2. Insert key into the ignition and wait for the interior lights to turn OFF.

3. Press and hold the power UNLOCK button on driver's side door panel. Do not release until instructed to do so.

4. Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just shy of starting your vehicle, OFF is the position where you can remove your key)

5. Release the power unlock button on the driver's side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock button then the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If the vehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotes must be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key too quick, too slow, there's a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.

6. Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30 seconds.

7. NOW repeat step 6. for all additional remotes including working ones.

8. After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.

9. Turn ignition to OFF, remove key and test all remotes.