2001 - 2007 OEM GM 4 Button Keyless Entry Remote w/ Trunk - L2C0007T

2001 - 2005 Buick Century
2001 - 2004 Buick Regal

Obtain all remote transmitters for this vehicle.

1. Close vehicle door.

2. Turn ignition to ON then back to OFF (ON is the position just shy of starting car without cranking engine)

3. Remove key from ignition.

4. Press and hold the UNLOCK switch on drivers door and continue to hold until instructed to release.

5. Insert key into the ignition (do not turn it) and remove it.

6. Insert key into the ignition (do not turn it) and remove it.

7. Insert key into the ignition (do not turn it) and leave it in.

8. Release the UNLOCK switch on drivers door. Vehicle will respond with three acoustic sounds to indicate successful entry into programming mode.

9. Press and hold the LOCK and UNLOCK buttons on first remote until vehicle beeps twice indicating successful programming. This step may take about 15 seconds.

10. Repeat step 9. for all remaining remotes including working ones.

11. Remove key from ignition to exit programming mode and test all remotes.

2002 - 2007 Buick Rendezvous

2001 - 2007 Pontiac Aztek

1. Close all doors.

2. Insert key into the ignition cylinder but do not turn it.

3. Press and hold the Unlock button on door lock switch on drivers door.
    Hold until instructed to release in step 6.

4. Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.

5. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.
   
6. Release door lock switch on drivers door panel.
    A Chime will sound 3 times indicating that you are in programming mode.

7. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
    A chime will sound 2 times if remote has programmed successful.

8. Repeat step 7 if you are programming additional remotes.

9. Remove key from ignition to exit programming mode.

NOTE: If you are having trouble getting this procedure to work, we have found that some vehicles need step 3 to be done before step 2.

2001 - 2003 Pontiac Grand Prix

IMPORTANT: Before entering programming mode, have in possession all of the remotes you
will be useing on the vehicle. Once you program the remote. all previous remotes that were
programmed will be erased from memory. The other remotes will not be functional until you
program the them again.

1. Remove the key from the ignition.

2. Close all doors.

3. Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or
    owner's manual to properly locate the "MALL PGM" fuse.

4. Insert the key into the ignition, and turn to the ACC position.

5. Turn the key to OFF and then back to ACC within 1 second.

6. Open and close any vehicle door. A chime will be heard when the system enters into
    programming mode.

7. Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds.
              IMPORTANT: After 7 seconds, a chime may be heard confirming successful
    synchronization. It is necessary to wait approximately 14 seconds for a second chime
    that will confirm successful programming.

8. Repeat step 7 now for each additional remotes to be programmed including any existing
    remotes.

9. Remove key from ignition.

10. Install the "MALL PGM" fuse back into the fuse panel and test remote(s).

2001 - 2002 Oldsmobile Intrigue

1.      Close the vehicle doors.    

2.      Turn OFF the ignition.    

3.      Remove the key from the ignition.   

4.      Press and hold the driver side door lock switch in the UNLOCK position.    

5.      Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)

6.      Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)

7.      Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.   

8.      Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.    

9.      Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).    

10.  Perform the previous step to program up to four transmitters (including your old ones).    

11.  Remove the ignition key in order to exit the Program Mode.