2002 - 2005 Chrysler/Dodge/Mitsubishi 3 Button Keyless Entry Remote Fob - OUCG8D-525M-A

SOME models come with self programming instructions. You can view them under the 'Programming Instructions' tab. All other models will need an automotive locksmith to come out and program the unit in for you. NOTE: When looking under the 'Programming Instructions' tab please look for your specific model as the programming instructions vary.

2002 - 2005 Chrysler Sebring

ATTENTION: You MUST HAVE one working remote to add one more to the system. 
If you do not have one working remote right now then these instructions will not work. 
You will have to have a Locksmith or dealership use a computer to program the first
remote for you.

1.  Using the working remote, 
     Press LOCK button 5 times at 2 second intervals to resynchronize remote. 

2.  Insert key into the ignition switch. Turn ignition to the RUN position (as far as you
     can go without cranking engine). Wait for ignition chimes to stop.

3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 
    10 seconds.

4. Still using the working remote, within the specified 4 to 10 seconds, continue 
    pressing the UNLOCK button and then press the PANIC button ( on the working 
    programmed remote ) for 1 second and release both buttons. A chime will sound 
    to indicate that the remote programming mode has been entered ( allow 3 seconds 
    for chime to sound ).

5. Still using the working remote, within 30 seconds of the chime, press and release the 
    LOCK and UNLOCK buttons simultaneously then press and release just the UNLOCK 
    button. A chime will sound indicating the remote has been programmed. 

6. Using a new / replacement remote, press and release the LOCK and UNLOCK buttons 
    simultaneously and then press and release just the UNLOCK button. A chime will 
    sound. This remote has now been programmed.

7. For each additional new /  replacement remote, press and release the LOCK and 
    UNLOCK buttons simultaneously and then press and release the UNLOCK button. A 
    chime should be heard after each remote signaling it has been programmed.

8. Turn ignition OFF and remove key.

9. Test Remotes.

2002 - 2005 Dodge Stratus

ATTENTION: You MUST HAVE one working remote to add one more to the system. 
If you do not have one working remote right now then these instructions will not work. 
You will have to have a Locksmith or dealership use a computer to program the first
remote for you.

1.  Press LOCK button 5 times at 2 second intervals to resynchronize remote. 

2.  Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can 
     go without cranking engine). Wait for ignition chimes to stop.

3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
     seconds.

4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then 
    press the PANIC button ( on the programmed remote ) for 1 second and release both 
    buttons. A chime will sound to indicate that the remote programming mode has been 
    entered ( allow 3 seconds for chime to sound ).

5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons 
    simultaneously then press and release just the UNLOCK button on the same remote.
    A chime will sound indicating the remote has been programmed. Press and release
    the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on
    each new remote you wish to program at this time. A chime will sound afer each 
    additional remote is programmed.

6. Turn the ignition OFF and remove key.

7. Test Remotes.

 2002 - 2005 Mitsubishi Galant w/o GTZ

 1.  Locate the Data Port under drivers side dashboard usually located to the right of steering column.

                    

       2.  Insert keys in ignition and leave in the OFF position.

       3.  Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port terminals 1 and 4 with a
            suitable jumper wire, leave the jumper wire connected throughout the programming procedure. Make sure you
            know which terminals are 1 and 4.

       4.  Within 10 seconds after connecting the jumper wire, press the Hazard Switch 6 times. Note: The doors will
             automatically lock and unlock once at this time indicating that the system is in the programming mode.

       5.  Press the LOCK  button on the remote to be registered three times within 10 seconds. Upon successful
            programming, the door will lock and unlock once.

       6.  Repeat step 5 with up to 4 remotes (including any existing remotes) within one minute. After completing each
             programming, the doors will lock and unlock once.

       7.  Disconnect the programming wire and remove the keys from the ignition.