2002 - 2009 Replacement GM and Isuzu 3 Button Keyless Entry Remote Fob - MYT3X6898B

Your Price $37.44
Availability: In stock
SKU
908-A
  • Buy 2 for $33.70 each and save 10%
  • Buy 3 for $31.82 each and save 15%

2002 - 2009 Replacement GM and Isuzu 3 Button Keyless Entry Remote Fob - MYT3X6898B

Fits:   

2004 - 2007 Buick Rainier
2002 - 2009 Chevrolet Trailblazer
2002 - 2009 GMC Envoy
2003 - 2008 Isuzu Ascender
2002 - 2004 Oldsmobile Bravada
2005 - 2007 Saab 9-7X

180 Day Satisfaction Guarantee!

If you are not 100% satisfied with your product for any reason, you may return the product within 180 days of ordering for a replacement. Please see our return policy for further information.

 

More Information
SKU908-A
FCC NumberMYT3X6898B
OE Part #15008008,15051014, 15008009
SupportYour purchase gives you 100% free e-mail and phone technical support from our expert staff.
Programming InformationMOST models come with self programming instructions. You can view them under the 'Programming Instructions' tab. All other models will need an automotive locksmith to come out and program the unit in for you. NOTE: When looking under the 'Programming Instructions' tab please look for your specific model as the programming instructions vary.
Product ConditionNew Aftermarket
Programming Instructions

2005 - 2006 Saab 9-7X

You must have all remotes including working ones when performing this procedure.


1. Close all doors and windows on the vehicle.


2. Insert key into the ignition and then wait for the dome light to turn off.


3. Press and hold the power UNLOCK button on driver's side door panel. Do not release until instructed to do so.


4. Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just shy of starting your vehicle, OFF is the position where you can remove your key)


5. Release the power unlock button on the driver's side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock button then the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If the vehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotes must be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key too quick, too slow, there's a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.


6. Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30 seconds.


7. NOW repeat step 6. for all additional remotes including working ones.


8. After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.


9. Turn ignition to OFF, remove key and test all remotes.

 

2004 - 2007 Buick Rainier
2002 - 2009 Chevrolet Trailblazer
2002 - 2009 GMC Envoy
2003 - 2008 Isuzu Ascender
2002 - 2004 Oldsmobile Bravada

You must have all remotes including working ones when performing this procedure.


1. Close all doors.


2. Insert key into the ignition.


3. Press and hold the power UNLOCK button on driver's side door panel. Do not release until instructed to do so in step 5.


4. Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just shy of starting your vehicle, OFF is the position where you can remove your key)


5. Release the power unlock button on the driver's side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock button then the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If the vehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotes must be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key too quick, too slow, there's a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.


6. Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30 seconds.


7. NOW repeat step 6. for all additional remotes including working ones.


8. After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.


9. Turn ignition to OFF, remove key and test all remotes.