2007 - 2017 NEW Replacement GM 5 Button Keyless Entry Remote w/ Remote Start/Liftgate - OUC60270/OUC60221

2008 - 2010 Buick Enclave
2007 - 2010 Cadillac Escalade
2007 - 2011 Chevrolet Tahoe
2009 - 2010 Chevrolet Traverse
2007 - 2010 Chevrolet Suburban
2007 - 2010 GMC Acadia

2008-2010 GMC Sierra
2007 - 2010 GMC Yukon

PROCEDURE #1
THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

1.Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)

2. Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.

3. Press the set/reset button (button will have a checkmark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.

4. Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.

5. Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.

6. To exit programming mode turn ignition OFF, remove key and test all remotes.

PROCEDURE #2
THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

1. Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).

2. Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.

3. Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.

4. Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.

5. Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.

6. To exit programming mode turn ignition OFF, remove key and test all remotes.

2007 GMC Sierra

Obtain all remote transmitters for this vehicle.

PROCEDURE #1 (FOR NEW BODY STYLE)

THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

1.Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine).

2. Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.

3. Press the set/reset button (button will have a checkmark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.

4. Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.

5. Repeat step 3. to program additional remotes. You can have up to 8 programmed remotes for this vehicle.

6. To exit programming mode turn ignition OFF, remove key and test all remotes.

PROCEDURE #2 (FOR OLD BODY STYLE)

THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVER INFORMATION CENTER.

1. Close all doors.

2. Insert key into the ignition.

3. Press and hold the power UNLOCK button on driver's side door panel. Do not release until instructed to do so.

4. Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just shy of starting your vehicle, OFF is the position where you can remove your key).

5. Release the power unlock button on the driver's side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock button then the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If the vehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotes must be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key too quick or too slow).

6. Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30 seconds.

7. NOW repeat step 6. for all additional remotes including working ones

8. After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.

9. Turn ignition to OFF, remove key and test all remotes.

2007 - 2010 Saturn Outlook

Obtain all remote transmitters for this vehicle.

PROGRAMMING WITH DRIVER INFORMATION CENTER

1: Switch ignition ON.

2: Press vehicle information button (located just to the right of the steering wheel) until PRESS TO RELEARN REMOTE KEY is displayed.

3: Press set/reset button (located just to the right of the steering wheel, will have a checkmark on it) until REMOTE KEY LEARNING ATIVE is displayed.

4: Programming mode now activated. Press and hold LOCK and UNLOCK buttons on the first remote for 15 seconds. When that remote is programmed an acoustic tone will be heard.

5: Repeat step 4 for any other additional remotes.

6: To exit programming mode switch ignition to off and then test all remotes.

PROGRAMMING WITHOUT DRIVER INFORMATION CENTER

1: Switch ignition on.

2: Press trip/odometer reset button (upper left of instrument cluster) until RELEARN REMOTE KEY is displayed.

3: Press and hold trip/odometer reset button for 3 seconds, REMOTE KEY LEARNING ACTIVE will be displayed.

4: Vehicle now in programming mode. Press and hold LOCK and UNLOCK buttons on first transmitter for 15 seconds

5: When an audible tone is heard first remote is programmed. Repeat step 4 for any other remotes.

6: To exit programming mode just switch key off.