2008 - 2012 Scion 3 Button Remote Head Key w/ Anti-Theft - NO CHIP - MOZB41TG

Dealer Price $232.86 Your Price $62.06 You save $170.8 That's 73.35% OFF dealer price!
Availability: In stock
SKU
2502

2008 - 2012 Scion 3 Button Remote Head Key w/ Anti-Theft - NO CHIP - MOZB41TG

IMPORTANTTo ensure you're purchasing correctly, please verify that your existing key does NOT have a letter "G", "H", or a 'dot' stamped into the blade. If your key has any of those three symbols on the key blade portion, this key will NOT work for you. Verifying the FCC ID number is also recommended. 

Fits:

2011 - 2012 Scion IQ
2008 - 2012 Scion TC
2008 - 2012 Scion XD

180 Day Satisfaction Guarantee!

If you are not 100% satisfied with your product for any reason, you may return the product within 180 days of ordering for a replacement. Please see our return policy for further information.

 

More Information
SKU2502
FCC NumberMOZB41TG
OE Part #89070-21180, 89070-52850
SupportYour purchase gives you 100% free e-mail and phone technical support from our expert staff.
Programming InformationSOME models come with self programming instructions. You can view them under the 'Programming Instructions' tab. All other models will need an automotive locksmith to come out and program the unit in for you. NOTE: When looking under the 'Programming Instructions' tab please look for your specific model as the programming instructions vary.
Product ConditionRefurbished
Programming Instructions

2008 - 2009 Scion tC


1. Driver's door open, key removed from ignition switch.

2. Within 5 seconds, insert and remove key from ignition switch twice.

3. Within 40 seconds, close and open driver's door twice.

4. Insert and remove key from ignition switch.

5. Within 40 seconds, close and open driver's door twice.

6. Insert key into ignition switch and close the driver's door.

7. Switch ignition ON and OFF once to program a remote while 

    retaining the original codes. Switch ignition ON and OFF twice 
    to program remote while erasing the original code. Switch ignition
   ON and OFF three times to check how many remotes are currently 
   registered or five times to erase all registered remotes.

8. Remove key from ignition switch.

9. System should now lock and unlock vehicle. Once, twice, or five times 
    depending on which mode has been selected. Once to four times, slowly,
    to indicate how many remotes are programmed.

10. Within 40 seconds: Press and release LOCK and UNLOCK buttons simultaneously.

11. Within 3 seconds: Press remote LOCK or UNLOCK button.

12. System should now LOCK and UNLOCK vehicle. Once to confirm registration,
      twice to indicate programming has failed.

13. Within 40 seconds, repeat step 10 to program additional remotes.
      Up to 4 remotes can be programmed.

14. To exit programming mode, open driver's door.


 2008 - 2010 Scion xD


Obtain all remote transmitters for this vehicle.

 

1. Start with the key out of the ignition, drivers door is open, all other doors and trunk closed and drivers door is unlocked.


2. Perform these steps within 5 seconds. A. Insert the key into the ignition (Do NOT Turn it) and Pull key out. B. Insert the key into the ignition (Do NOT Turn it) and Pull key out.


3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition (Do NOT Turn it) and Pull key out.


4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in the ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start or crank engine) then back to OFF. F. Remove the key from the ignition.


5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point.


6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.


7. Open drivers door.


msrp232.86