2008 - 2013 Cadillac CTS/DTS 5 Button Keyless Entry Remote Fob - OUC6000066

2008 - 2013 Cadillac DTS Programming Instructions: Please Check your Manual for Instructions as Cadillac's are Self-Programmable and Instruction's are Normally in your Owner's Manual.

1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
    PRESS TO RELEARN REMOTE KEY displays 

3. Press the set/reset button until 
    REMOTE KEY LEARNING ACTIVE  displays

4.  Press and hold the lock and unlock buttons on the first keyless remote at the same 
     time for approximatley 15 seconds. (On vehicles with memory recall seats, the first 
     remote learned with match driver 1 and the second will match driver 2.)

     A chime will sound indicating that the remote is programmed.

5.  To program additional remotes at this time repeat step 4.
      This vehicle can have a maximum of eight remotes programmed.

6.  To exit programming mode turn key off and remove key.
     Test remote(s).

2008 - 2009 Cadillac CTS Programming Instructions: Please Check your Manual for Instructions as Cadillac's are Self-Programmable and Instruction's are Normally in your Owner's Manual.

 Use this Procedure for Vehicles with 

Driver Information Center Buttons

1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
    PRESS TO RELEARN REMOTE KEY displays 

3. Press the set/reset button until 
    REMOTE KEY LEARNING ACTIVE  displays

4.  Press and hold the lock and unlock buttons on the first keyless remote at the same 
     time for approximatley 15 seconds. A chime will sound indicating that the remote is 
     programmed.

5.  To program additional remotes at this time repeat step 3.
      This vehicle can have a maximum of eight remotes programmed.

6.  To exit programming mode turn key off and remove key.
     Test remote(s).

Use this Procedure for Vehicles without
Drivers Information Center Buttons

To access this display, the vehicle must be in Park (P) with key in the on position (as far
    as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays. 

2. Press and hold the trip odometer reset stem for three seconds.
    The message  REMOTE KEY LEARNING ACTIVE  will display 

3.  Press and hold the lock and unlock buttons on the first keyless remote at the same 
     time for approximately 15 seconds. A chime will sound indicating that the remote is 
     programmed.

4.  To program additional remotes at this time repeat step 3. 
     This vehicle can have a maximum of eight remotes programmed.

5.  To exit programming mode turn key off and remove key.
     Test remote(s).

2010 - 2013 Cadillac CTS Programming Instructions: Please Check your Manual for Instructions as Cadillac's are Self-Programmable and Instruction's are Normally in your Owner's Manual.

   You have one programmed remote and you want to add another.

1. Vehicle must be off.

2. Place the working remote(s) in the cupholder. Have the new remote with you.

3. Insert the key into the key lock cylinder located on the outside of drivers door.

4.Turn the key to the unlock position five times with in five seconds.

5. The (DIC) Driver Information Center displays Ready to Learn Electronic key #2, 3 or 4

6. Place the new remote into the transmitter pocket with the buttons facing the front
    of the vehicle. (The transmitter pocket is inside the center console between the 
    driver and front passanger seats).

7. A beep sounds once the remote is programmed. The DIC displays Ready to Learn
    Electronoic Key #3 or 4, Or Maximum # Electronic Keys Learned.

8. Press the ignition control knob to exit programming mode.

9. Remove the remote from the transmitter pocket and press unlock to the remote two times.

10. To program additional remotes, repeat Steps 6 through 9.

      You have no working remotes. 

1. The vehicle must be off.

2. Place the new remote into the transmitter pocket with the buttons facing the front
    of the vehicle. (The transmitter pocket is inside the center console between the 
    driver and front passanger seats).

3. Insert the key into the key lock cylinder located on the outside of drivers door.

4.Turn the key to the unlock position five times with in five seconds.

5. The (DIC) Driver Information Center displays Ready to Learn Keys.

6. Press the ignition switch in.

7. The DIC reads Learn Delay Active Wait XX Min and counts down to zero.

8. The DIC displays Press Start Control To Learn Keys again.

9. Press the ignition switch in again.

10. Repeat Steps 7, 8 and 9

11. The DIC reads Learn Delay Active Wait XX Min and counts down to zero.

12. A beep sounds and the DIC reads Ready To Learn Electronic Key # X.
       All reviously known remote programming has been erased.

13. A beep sounds once programming is complete. The DIC displays Ready To Learn 
      Electronic Key #2

14. To program additional remotes, insert each transmitter in the pocket until a beep is 
       heard and the DIC advances to the next electronic key number. Up to four remotes 
       can be programmed. The DIC dislpays Maximum # Electronic Keys Learned and 
       exits the programming mode.

15. Press the ignition control knob if programming is complete.

16. Press unlock on each newly programmed remote to complete the process.