2008 - 2016 Toyota Sequoia 4 Button Keyless Entry Remote w/ Hatch - GQ43VT20T

Dealer price: $178.63

Your price: $68.00

You Save: $110.63

That's 61.93% OFF dealer price!

In stock
2008 - 2016 Toyota Sequoia 4 Button Keyless Entry Remote w/ Hatch - GQ43VT20T

2008 - 2016 Toyota Sequoia 4 Button Keyless Entry Remote w/ Hatch - GQ43VT20T

Fits:

2008 - 2016 Toyota Sequoia

Product Specs and Programming Information
SKU 2730
FCC Number GQ43VT20T
OE Part # 89742-0C040
Support Your purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee! If you are not 100% satisfied, you may return the product within thirty days of receipt for a refund. Please see our return policy for further info.
Programming Information This remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab.
Product Condition Refurbished
Programming Instructions

2008 - 2009 Sequoia

 

Obtain all remote transmitters for this vehicle.

 

1. Start with the key out of the ignition, drivers door is open, all other doors and trunk closed and drivers door is unlocked.


2. Perform these steps within 5 seconds. A. Insert the key into the ignition (Do NOT Turn it) and Pull key out. B. Insert the key into the ignition (Do NOT Turn it) and Pull key out.


3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition (Do NOT Turn it) and Pull key out.


4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in the ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start or crank engine) then back to OFF. F. Remove the key from the ignition.


5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point.


6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.


7. Open drivers door.

 

Alternative Instructions for 2008 Sequoia

 

1. Start with key out of ignition, drivers door is open all others closed and 
    drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.

3. Perform these steps within 40 seconds.
    A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
        starting with lock. Use an even pace and try to go about one cycle per second.
        (1Cycle  = 1 lock and 1 unlock).
    B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
    A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
        starting with lock. Use an even pace and try to go about one cycle per second.
         (1Cycle  = 1 lock and 1 unlock).
    B. Insert the key in the ignition cylinder.
    C. Turn the ignition to ON (Do NOT Start) then back to OFF.
    D. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful
    entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
    B. Immediately after letting go of the lock and unlock buttons, press the lock button by
        itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle once
        indicating successful programming. If the door locks do not cycle, or cycle twice.
        repeat steps A and B in step 6 as your remote has not been accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Close drivers door.

msrp $178.63
Copyright © 2019-present Replacemyremote.com All rights reserved.