2013 - 2015 Cadillac 5 Button Smart Key w/ Remote Start - Emergency key included - NBG009768T

2013 - 2015 Cadillac 5 Button Smart Key w/ Remote Start - Emergency key included - NBG009768T

2013 - 2015 Cadillac 5 Button Smart Key w/ Remote Start - Emergency key included - NBG009768T

Dealer Price $215.08 Your Price $122.99 You save $92.09 That's 42.82% OFF dealer price!
Availability: In stock
SKU
474

2013 - 2015 Cadillac 5 Button Smart Key w/ Remote Start - Emergency key included - NBG009768T

Emergency Key: SKU:459

Fits:

2013 - 2014 Cadillac XTS
EARLY 2015 Cadillac XTS
2013 - 2014 Cadillac ATS
2014 Cadillac ELR

More Information
SKU474
FCC NumberNBG009768T
OE Part #22586930, 22856930
SupportYour purchase gives you 100% free e-mail and phone technical support from our expert staff.
180 Day Satisfaction Guarantee!If you are not 100% satisfied, you may return the product within thirty days of receipt for a refund. Please see our return policy for further info.
Programming InformationThis remote comes with self programming instructions. You can view them under the 'Programming Instructions' tab.
Product ConditionRefurbished
Programming Instructions

Programming with a Recognized Transmitter


A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be off and all transmitters, both currently recognized and new, must be with you.


1. Open the center console storage area and the storage tray.

2. Place the recognized transmitter(s) in the pocket. The transmitter pocket is inside the center console storage area between the driver and front passenger seats.

3. Remove the key lock cylinder cap. See Door Locks on page 2-10. Insert the vehicle key into the key lock cylinder on the driver door handle. Then turn the key counterclockwise, to the unlock position, five times within 10 seconds. The Driver Information Center (DIC) displays READY FOR REMOTE #2, 3, 4, ETC.

4. Replace the recognized transmitter with a new transmitter. Place the new transmitter in the transmitter pocket.

5. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.

6. Remove the transmitter from the transmitter pocket and press K or Q on the transmitter. To program additional transmitters, repeat Steps 3–5. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode.

 

Programming without a Recognized Transmitter


If there are no currently recognized transmitters available, follow this procedure to program up to eight transmitters. This feature is not available in Canada. This procedure
will take approximately 30 minutes to complete. The vehicle must be off and all transmitters to be programmed must be with you.


1. Remove the key lock cylinder cap. See Door Locks on page 2-10. Insert the vehicle key into the key lock cylinder on the driver door handle; then turn the key counterclockwise, to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays REMOTE LEARN PENDING, PLEASE WAIT.

2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/STOP button. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.

3. Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show READY FOR REMOTE # 1.

4. Place the new transmitter in the transmitter pocket. The transmitter pocket is inside the center console storage area between the driver and front passenger seats. The storage area will need to be opened to access the transmitter pocket.

5. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.

6. Remove the transmitter from the transmitter pocket and press K or Q on the transmitter. To program additional transmitters, repeat Steps 4–6. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode.

msrp215.08